Q&A

[Penetration Testing] Top 70 Most Interview Questions

As you prepare for your pentester interview, you may be considering which questions the employer is going to ask you. While there’s no way to know for sure what topics will be covered because information security is a huge field, there are several popular interview questions you can expect to be asked. Being a pentester […]

Q&A

CCNA Interview Questions – Part 5

Part 1 | Part 2 | Part 3 | Part 4 | Part 5 Question 81: Explain the basic steps involved in converging a link state inter network. Answer: Each router floods a link state information advertisement describing its links, the states of its links, and any neighboring routers connected to those links, throughout the […]

Q&A

CCNA Interview Questions – Part 4

Part 1 | Part 2 | Part 3 | Part 4 | Part 5 Question 61: What is a summary route? In the context of static routing, how are summary routes useful? Answer: A summary route is a single route entry that points to multiple subnets or major IP addresses. In the context of static […]

Q&A

CCNA Interview Questions – Part 3

Part 1 | Part 2 | Part 3 | Part 4 | Part 5 Question 41: What is fragmentation? What fields of the IP header are used for fragmentation? Answer: Routers perform fragmentation when a packet is longer than the maximum packet length (Maximum Transmission Unit, or MTU) supported by a data link onto which […]

Q&A

CCNA Interview Questions – Part 2

Part 1 | Part 2 | Part 3 | Part 4 | Part 5 Question 21: What is the primary purpose of a LAN? Answer: The primary purpose of a local-area network is to allow resource sharing. The resources may be devices, applications, or information. Examples of shared resources are files, databases, e-mail, modems, and […]

Q&A

CCNA Interview Questions – Part 1

Part 1 | Part 2 | Part 3 | Part 4 | Part 5 Question 1: Which layer of the OSI model is responsible for reliable connections? Answer: The Transport layer of the OSI model is responsible for reliable connections. Question 2: What is the difference between acknowledgements and handshaking? Answer: Handshaking is used to […]

Q&A

Windows MCQ – 1 to 20 With Answers

1. Device A has been configured for IRQ 3. Which of the following devices will Device A potentially conflict with? A. COM1 B. LPT1 C. COM2 D. LPT2 2. What is the default IO address assigned to COM1? A. 02F8 B. 0378 C. 03F8 D. 0278 3. Which of the following best describes DMA? A. […]

Q&A

Computer Fundamentals MCQ with Answers – 35 Set

1. Which of the following components is not usually found on a motherboard? A. Hard drive controller B. DVD drive controller C. Memory D. Video adapter 2. What type of memory is not usually found on a motherboard? A. CMOS memory B. L1 Cache C. L2 Cache D. DIMM 3. The power supply converts 110 […]

Q&A

20 Basic Computer Questions With Answers

1. What was the original system board speed of the ATX board? A. 33 MHz B. 60 MHz C. 66 MHz D. 100 MHz 2. Which bus architecture supports 32-bit / 64-bit cards and transfers information at 33 MHz? A. ISA B. EISA C. AGP D. PCI 3. Which motherboard component is responsible for charging […]

Q&A

Hardware Basic Questions With Answers – 33 Set

1. You have a USB camera in which you are trying to copy some of the pictures to the computer’s hard disk. The computer does not seem to recognize the device. What should you do? A. Check to see that the boot order is correct. B. Make sure that the USB ports are enabled. C. […]

Q&A

Computer Printer MCQ With Answers – 25 Set

1. What are the two types of paper feeder mechanisms? A. Continuous tractor feed B. Continuous form feed C. Friction feed D. Injected 2. What type of printer is most likely to use a continuous form feeder? A. Laser printer B. Inkjet C. Dot-matrix D. USB 3. Which of the following devices are most likely […]

Q&A

General Computer MCQ – With Answers

1. Which type of memory cannot be upgraded without replacing a CPU? A. RAM B. L1 cache C. L2 cache D. None of the above 2. Which type of the system BIOS can be upgraded? A. Flashable B. Non-flashable C. Both types D. None 3. Which of the following utilities cannot be used to identify […]